Linksys Velop Red Light – Meaning and Troubleshooting
Since the Linksys Velop mesh WiFi system consists of various units called nodes, the red light can show up on any of them. You might be well aware of the fact that every node has only one LED light that illuminates various colors and red is one of them. You can see the red light on the Parent node and the Child node both. For your information, the node that directly connects to the modem is called the Parent or the Primary node. On the other hand, all other units (nodes) share a wireless connection with the Primary one, hence called Secondary or Child nodes. In this blog, we have tried to address the Linksys Velop red light problem with respect to the Parent as well as the Child node. Stick to reading to find out how to resolve the issue on the device that is illuminating red.
What Does the Linksys Velop Red Light Mean?
Let’s start the troubleshooting process by understanding the meaning of the red light on the Linksys Velop nodes. The table given below will provide you with an overview of the same.
| Velop Node Red Light Status |
Parent Node | Child Node |
|---|---|---|
| Solid Red | No internet connection is there | No internet connection |
| Blinking Red | Your node isn’t connected to the modem | The Child node isn’t connected to the Parent node |
In simple words, the red light is an indication of the internet connectivity issue with the mesh system that can further halt your access to the Linksys router login page. Let’s hope that you are now familiar with the reason why you are experiencing the red light problem with your Velop nodes. Considering that, we are now making our way to the troubleshooting portion that will house the techniques to troubleshoot the issue easily.
How to Troubleshoot Linksys Velop Red Light?
Walking through this section will provide you with a deep insight into addressing the red light problem with your Parent node along with the Child node. But, before you do that, consider making a small effort to restart the entire Velop system. Perhaps, all your Velop node is experiencing is a technical glitch that is forcing it to illuminate red. Restarting can help you combat them.
Restarting the Velop System
To restart the Velop system properly, you are required to switch off the Parent node first and then disconnect it from the modem. After that, power down other nodes one after another. Once done, wait for a decent amount of time. Let’s say 20 minutes. Power up your Linksys nodes in the same sequence as you powered them down.
Tip 1: Check the Ethernet Connection
The solid red color on the LED light of your Linksys Velop Parent node was a sign that there was no internet connection on it. Since the Parent node gets the internet connection from the modem, it means it is the router-modem connection that is foiling the entire internet play. So, you are required to check the same and verify if the Ethernet connection is finger-tight or not. If not, then do the needful. Besides, check for cuts on the cable. There aren’t supposed to be any. Replacing the cable will be the wisest thing to do if it is found damaged.
Tip 2: Bring the Parent and Child Nodes Closer
You are now suggested to bring your Child (Secondary) node a little closer to the Parent (Primary) node. There needs to be a safe distance between two Linksys nodes. It means you are supposed to place them very optimally. But, know that you cannot place two nodes very close as it might result in a clash of WiFi signals causing major issues instead of fixing the Linksys Velop red light. It must be known to you that Velop nodes do not need to see each other in order to communicate properly. Their presence in each other’s range is sufficient.
Tip 3: Eliminate WiFi Interference
There is a chance that your Velop nodes are not getting connected to the internet because of the physical impedances present between their paths of communication. So, your next task should be to clear that path. Ensure that there is no microwave oven, television, refrigerator, treadmill, aquarium, metal door, mirror, baby monitor, Bluetooth speaker, etc. present near your Velop nodes. In addition to that, be very certain that none of your Velop nodes are present in a corner or near a thick concrete wall.
As a Final Observation
From the very beginning, it is very clear that the Linksys Velop red light issue is an indication of the internet connection error. That is why fixes related to the issue are revolving around the solutions to fix internet connectivity. The post covered all the major aspects of fixing the red light on the Velop node. It is now expected that you have successfully fixed the issue and the node is now flashing blue. To make the most out of your home network, consider updating the firmware of your Linksys nodes.
